Foundry Networks FGS648P-POE Instrukcja Użytkownika Strona 76
- Strona / 96
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
FastIron GS Compact Layer 2 Switch Hardware Installation Guide
7 - 8 © 2007 Foundry Networks, Inc. September 2007
NOTE: The handle on the front panel of the power supply may block access to the negative and positive
terminal screws. You may need to temporarily remove the receptacle for the positive and negative terminals if
you can’t access the screws used to hold the wires in the connectors. The figure below shows the screws that
secure the receptacle to the power supply.
6. Connect the ground, positive and negative wires as follows:
• Slip the ground wire into the opening under the marking until the wire is fully in place, then use the
crimper to crimp the lug snugly onto the wire. Gently pull the lug away from the wire to verify that the lug
is securely fastened.
• Connect the -48 VDC lead to the negative (—) terminal and tighten the negative terminal screw.
• Connect the 48 RTN lead to the positive (
+) terminal and tighten the positive terminal screw.
The following illustration shows how to connect the wires on a DC power supply.
7. Pull gently on each wire to make sure they are securely fastened in the connector.
8. If you removed the receptacle for the positive and negative terminals, re-position it and secure the two screws.
9. With one hand, hold the handle on the front panel of the power supply. With the other hand, support the
underside of the power supply, and insert the power supply into the empty power supply slot. Press until the
supply is completely in the slot, so that the connectors on the back of the supply are fully engaged with the
pins on the power backplane.
CAUTION: Make sure you insert the power supply right-side up. It is possible to insert the supply upside
down, although the supply will not engage with the power backplane when upside down. The power supply is
right-side up when the power connector is on the left and the fan vent is on the right.
10. Press the two latches near the edges of the supply outward to lock the supply in place.
11. Replace the power supply locking screw.
12. Power on the supply and verify that it is working properly as instructed in “Powering On the System” on
page 3-14 and “Verifying Proper Operation” on page 3-15.
Ground
+
–
- Foundry FastIron GS 1
- Compact Layer 2 Switch 1
- POE and POE-Upgradeable 1
- Hardware Installation Guide 1
- Contents 3
- HAPTER 4 4
- HAPTER 5 4
- HAPTER 6 5
- HAPTER 7 5
- APPENDIX A 6
- APPENDIX B 6
- Chapter 1 7
- About This Guide 7
- Related Publications 8
- How to Get Help 8
- Warranty Coverage 8
- Chapter 2 9
- Product Overview 9
- Software Features 10
- Hardware Features 10
- FGS624XGP and FGS624XGP-POE 11
- FGS648P and FGS648P-POE 11
- Control Features 12
- Optional 2-port 10-GbE Module 13
- (slot 2, ports 1 and 2) 13
- 1-port 10-GbE Module 13
- (slot 3, port 1) 13
- Reset Button 14
- Network Interfaces 14
- 1 XFP port 15
- 2 XFP ports 16
- 10GbE 2-port CX4 Module 17
- 10GbE XG and CX4 Module 17
- Fiber Optic Modules 20
- Power Supplies 20
- Cooling System and Fans 21
- Chapter 3 23
- Summary of Installation Tasks 24
- Installation Precautions 25
- Power Supply Precautions 26
- Cabling Infrastructure 27
- Installation Location 27
- Power supply 28
- Retaining Bale AC Power Cord 29
- Positive terminal screw 31
- DC Power Supply 32
- Plug on rear of 32
- Installing the Device 33
- Wall Mount Installation 35
- Powering On the System 36
- Attaching a PC or Terminal 38
- Chapter 4 41
- Checking Connectivity 41
- Configuring IP Addresses 43
- Connecting Network Devices 44
- Automatic MDI/MDIX Detection 45
- Testing Connectivity 46
- Observing LEDs 47
- Tracing a Route 48
- Chapter 5 51
- Removing MAC Address Entries 53
- Chapter 6 55
- Hardware Specifications 55
- Chassis Specifications 56
- Air inlet 57
- Air exhaust 57
- Power Source Interruptions 58
- Mean Time Between Failure 58
- Power Draw Specifications 59
- Pinouts and Signalling 60
- Cable Specifications 61
- Power Supply Specifications 63
- Key features 64
- Environmental Considerations 64
- Power Supply Consumption 65
- Input Connector and Plug 66
- Regulatory Compliance 67
- Safety Warnings 67
- Electrical Specifications 68
- Chapter 7 69
- AC Power Supplies 70
- Locking screw 71
- Disassembling the Chassis 79
- Figure 7.7 POE Daughter Card 80
- POE Daughter Card 81
- POE Daughter Cards 82
- Removing a Fiber Optic Module 83
- Bail Latch 83
- Cabling a Fiber Optic Module 84
- Digital Optical Monitoring 85
- Supported Media 86
- CLI Commands 86
- Appendix A 87
- Regulatory Statements 87
- Appendix B 89
- Cautions and Warnings 89
- Warnings 94
Powiązane produkty i podręczniki dla Networking Foundry Networks FGS648P-POE
(56 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 4.834 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji